Corsair H150i Pro Amd Mounting Hardware

H150i PRO RGB

LOW Racket 360MM RGB LIQUID CPU COOLER
QUICK Starting time GUIDE

Notation: Virtually newer PC cases include a CPU cutout to allow access to the bottom of the motherboard. If your example does non include a cutout, you volition need to remove your motherboard from the case before installation.

Included Hardware

Highlighted parts for Intel installation simply. Note: The H150i PRO RGB comes with Intel mounting bracket pre-installed on the pump for quick installation.

Installing the Intel Backplate

• For LGA 115X installation, slide the backplate pins within (figure 1).
• For LGA 1366 installation, slide the backplate pins exterior (figure 1).
• Install the assembled backplate (figure ii).

Note: Intel LGA 2011 and LGA 2066 does not require backplate installation. Proceed to footstep 2.

Installing the Intel Collision Screws

• Attach the provided Intel standoff
•  Use (B) for LGA 115X/1366, or (C) for LGA 2011/2011-3/2066.
•  Tighten all four screws until firmly secure.

Install the Fans and Radiator

Attach the radiator and the fans every bit shown. For the best cooling performance, we recommend mounting the fans as an air-intake to
your PC case.

Installing the Pump Unit

• Align the bracket and pump over the standoff screws as shown.
•  Tighten the thumbs screws until all four corners are firmly secured.

Connect Power to the Fans and Pump

• Connect the pump power cablevision to an available SATA power plug (effigy one).
• Connect pump tach cable to the CPU_FAN header on your motherboard (figure 1).
•  Connect each fan to the shrouded four pin connectors on the pump (figure 2).

Using the included CORSAIR iCUE USB cable, adhere the pump unit to a motherboard USB header.

AMD

Included Hardware

Installing the AMD Mounting Bracket

Note: It is important that the AMD retention bracket exist evenly secured on all sides before installation!

•  Remove the integrated Intel mounting bracket by turning the mounting bracket, and pulling abroad from the copper coldplate (figure ane).
• Install the AMD bracket past aligning the twist lock, pushing in, turning the contrary direction, and allowing subclass to secure (figure 2).

Install the Fans and Radiator

Adhere the radiator and the fans as shown. For the all-time cooling functioning, nosotros recommend mounting the fans as an air-intake to your PC instance.

Fix the Mounting Bracket

Insert the AMD screw clips and secure them with the screws every bit shown. Do not tighten the thumbscrews all the way

Install the Pump Unit

Align the bracket with the Stock AMD mounting clips equally shown. Tighten the thumbscrews until secure.

Connect Power to the Fans and Pump

• Connect pump power cable to an bachelor SATA power plug (figure 1).
• Connect pump tach cable to the CPU_FAN header on your motherboard (figure 1).
• Connect each fan to the shrouded 4 pin connectors on the pump (figure 2).

Using the included CORSAIR iCUE USB cable, attach the pump unit to a motherboard USB header.

FAQ

1. How exercise I know the management of the airflow of the fan?
   An pointer located on the side of the fan indicates the management of airflow.
2.  Tin can I reuse the pre-applied thermal paste on the H150i PRO RGB for a re-installation?
   Re-installation of the H150i PRO RGB libation will crave you lot to clean off the pre-applied thermal paste and utilise an aftermarket paste.
3. Where can I purchase boosted radiator screws for push/pull Configuration?
   Boosted screws can be purchased from www.corsair.com.

Thank you for purchasing the CORSAIR Hydro Serial H150i PRO RGB Depression Noise Liquid CPU Cooler.
Please visit: corsair.com to download a detailed user guide or to obtain technical support.

Annotation ON Ecology PROTECTION:
After the implementation of the European Directive 2012/xix/Eu in the national legal organization, the following applies:
– Electrical and electronic devices may not be disposed of with domestic waste.
– Consumers are obliged past law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or bespeak of auction. Details to this are divers by the national law of the respective country. This symbol on the product, the teaching manual, or the parcel indicates that a product is field of study to these regulations. By recycling, reusing the materials, or other forms of utilizing sometime devices, y'all are making an of import contribution to protecting our environment.

CORSAIR Memory, Inc. declares that this equipment is in compliance with Directive 2014/30/EU and Directive 2011/65/EU. A copy of the original announcement of conformity can be obtained at [email protected]

	© 2017 – 2019 CORSAIR MEMORY, INC. All rights reserved. CORSAIR and the sails logo are registered trademarks in the United States and/or other countries. All other trademarks are the property of their corresponding owners. Production may vary slightly from those pictured. 49-001595 AD
	47100 BAYSIDE PARKWAY • FREMONT • CALIFORNIA • 94538 • USA

Documents / Resources

References

Share this post